The RAM WORLD WIDE WEB SITE
Quality Products Since 1976
Since 1980 RAM has used the highest quality instrument bulbs available to manufacturers. Their brightness, long life and low current drain have been proven in thousands of RAM products. Unless specified, the systems listed below are powered by a compact, 1.5 ounce, 9 volt alkaline battery or a 6 cell nicad. The systems are light and compact, completely assembled in the U.S.A. and ready for installation.
Most systems are supplied with appropriately colored lenses which fit over the various bulb sizes. The 01, 05, 15, 20, 21, 33, 34, 36 and 66 utilize a 3/16 inch diameter, flat top lens. The 14 system uses a 1/4 inch diameter, flat top lens. The 02, 04 and 23 are supplied with a 3/8 inch diameter, dome top lens. Information for obtaining optional bulbs and lenses is included in each light system package.
LIFETIME BULB WARRANTY. RAM instrument quality bulbs are warranted against burnout for the life of your lighting system. If a bulb fails, snip it off with a 1 inch wire, insert it in a slot cut into a 3 by 3 inch square of corrugated cardboard, note the number of the lighting system and mail it to RAM. Obviously, this does not apply to bulbs that have been broken in use or installation or have been powered beyond specified voltage limits. Include $1.00 to cover packing and postage.
LIFETIME BULB WARRANTY. RAM instrument quality bulbs are warranted against burn out for the life of your lighting system. If a bulb fails, snip it off with a 1 inch wire, insert it in a slot cut into a 3 by 3 inch square of corrugated cardboard, note the number of the lighting system and mail it to RAM. Obviously. this does not apply to bulbs that have been broken in use or installation or have been powered beyond specified voltage limits. include $1.00 to cover packing and postage.
RAM 01 PROGRAMMABLE FLASHING NAVIGATION LIGHTS.
This system now features wing light wires to provide for a span of 94 inches which will accommodate 90% of the model kits currently available. A Deans connector provides for easy wing removal.
The flash rate and duration of the red and green wing tip lights and the clear tail light are adjustable through a wide range to duplicate any scale operation. The assembled system contains the flasher circuit board with a 9 volt battery snap, connected to the wires and bulbs described above.
Approximate weight, 1 ounce.
RAM 02 ADJUSTABLE RATE "STROBE" LIGHT.
The light is adjustable to any desired flash rate. The system contains an adjustable rate flasher circuit board, 1 high intensity bulb on three feet of wire, battery snap connector and a clear dome lens. The system provides a bright, adjustable strobe light effect. Weight approximately 1/2 oz.
RAM 03 LANDING LIGHTS.
System contains a positive pulse electronic switch and 2 high intensity bulbs with fixtures. It is connected to the receiver to work independently or simultaneously with another control function and uses the 4.8 volt RX. pack for power. Weight approximately 1 oz., with generic receiver connector.
RAM 04 ADJUSTABLE RATE MARS "ROTATING" BEACON.
The light is adjustable to the desired "rotation" rate. The system contains an adjustable "rotation" unit, 1 high intensity bulb on three feet of wire, battery snap connector, and one red dome lens. Weight approximately 1/2 oz.
RAM 05 MARINE NAVIGATION LIGHTS
(non-flashing, may be used for some aircraft types). System contains 3 high intensity bulbs, each on three feet of wire, with red, green and clear lenses, battery snap connector. Provides standard navigation lights. Weight 1/2 oz.
RAM 06 SKY LIGHTS.
This system is the proven way to fly at night or in low visibility. Three light strands. containing 6 bulbs each, are used to light each wing and the fuselage so flight orientation is maintained with the familiar 'T' shape of a lighted plane against a black sky. The model must be of "built up" construction with little planking and covered with a translucent material such as made by Monokote. The assembled system provides for models up to 94" span and includes a Deans connector to detach the wing and a master switch. Using a 7.2 to 9 volt battery will result in a total glowing effect that cannot be matched by any other light system.
RAM 07 LIGHT BAR. (Cars)
The molded plastic light bar is 31/2" long with a chrome base and 2 red lenses, perfect for 1/10 and 1/12 scale vehicles. The system includes an adjustable rate flash unit with two bulbs each on 12" of wire. A 9 volt battery snap is provided or 6 cell car nicads can be used. Blue and amber lenses are available from RAM.
RAM 10 GAS CAR HEADLIGHTS, TAIL & STOP LIGHTS. (Cars)
Designed to provide an efficient 9 volt alkaline battery powered lighting system for gas powered cars and trucks. The system includes two of our #19 type headlights for easy installation. Two red tail lights, controlled by a micro switch, shift to bright stop lights anytime the throttle linkage drops from full power. Installation details and tips are included in the instructions.
RAM 13 HEAD LIGHTS. (Cars)
Designed for Tamiya etc. molded grills. Two bayonet style, 1/4" bulbs, each on 12" of wire, allow easy installation. Comes with a 9 volt battery snap or 6 cell car nicads can be used.
RAM 14 BIG AIRPLANE NAVIGATION LIGHTS.
System contains 3 superbright bulbs, with red, green and clear lenses, a six-foot tail lead, 2 sevenfoot wing tip leads with Deans connectors, switch, and a 6 AA cell battery box. Nicad or alkaline cells are required. Weight 3 oz.
RAM 15 NON FLASHING NAVIGATION LIGHTS.
This set provides for models not needing flashing lights and also features wing wires for up to 94" models and a Deans connector for easy wing removal. Instrument bulbs with red, green and clear lens covers are powered by an alkaline 9 volt battery or a 6 cell nicad pack. Approximate weight, 1/4 ounce.
RAM 16 ECONO LANDING LIGHTS.
System contains 2 superbright bulbs rated at 2800 beam candlepower each on 2 feet of wire, with new, 5/8" diameter, aluminum, focused reflectors, microswitch, battery snap connector. Switch attaches to retract, flap, or motor servo for control. Weight 1 oz.
RAM 19 HEAD LIGHTS. (Cars)
The aluminum 5/8" diameter reflector protects the bulb in the toughest crash. Two lights, each on 12" of wire, allow easy installation. Comes with a 9 volt battery snap or 6 cell car nicads can be used.
RAM 20 TAIL & STOP LIGHTS. (Cars)
This system is comprised of two red stop lights, each on 12" of wire, and a switching device that is simply wired to the electric vehicle's drive motor. Whenever forward power is reduced, the bulbs will go from a dim tail light to a bright intensity for brakelight effect. No power is drawn from the motor battery 9 V battery powers the system.
RAM 21 TURN LIGHTS. (Cars)
Four amber lites are used to duplicate scale vehicle operation. Two microswitches control a flasher device to simulate turn light action automatically when the vehicle is maneuvered. Comes with a 9 V battery snap or 6 cell car nicads can be used.
RAM 23 REAL STROBE LIGHT.
This is the smallest, lightest, safest, xenon strobe ever offered to the R/C modeler. The unit is 3/4 " X 1 " x 1 1/2". The encased flash tube is 1/8" x 1 " on a 10" cord. Total weight, 1 oz., under 3 ounces with 2 AA cells which will power the unit up to 8 hours. Comes with battery box and a clear lens cap.
RAM 24 RAM LITES. (Cars)
Two off road style, all aluminum lights for roll bar or body mounting. The black anodized 1/2" long threaded base provides easy mounting. The 1 " diameter satin finished body can be used as is or polished to a high gloss. A 9 V battery or 6 cell car nicads can be used.
MORE LIGHTING SYSTEMS
RAM 28 RAM LIGHTS w/ TAMIYA ROLL BAR MOUNTS. Two #24 RAM Lites are packaged with two adaptors which mount to the Tamiya or similar roll bar.
RAM 29 RAM LITES with / FOLD AWAY ROLL BAR. (Cars)
Now you can have a roll bar that won't tear up your light plastic truck bodies when they roll over. Two #24 RAM Lites are supplied with adaptors and all hardware to make a fold away roll bar which adapts to any R/C body.
RAM 33 PACE CAR 10 LIGHT SET. (Cars)
Add the excitement of a Pace Car to your collection of car bodies. This set includes 2 #19 Headlights with aluminum reflectors, 2 tail lights with red lenses, 4 flashing hazard lights with amber lenses and a RAM 07 Light Bar with 2 flashing bulbs and an adjustable rate flasher all wired into one system. You can use a 9 volt alkaline battery or a 6 cell car nicad pack for power.
RAM 34 CLEARANCE LIGHTS. (Cars)
This 8 light set provides for all 4 sides of a truck, tractor or trailer. The 3/16 inch diameter, round, amber lenses are a near perfect replica of commonly used clearance, marker and running board lights. Use a 9 volt alkaline battery or your 6 cell car pack.
RAM 36 CAB MARKER LIGHTS. (Cars)
These assembled, scale lights are 1 inch long, have amber lenses and are ready for quick installation. They are aluminum, rugged and AMERICAN MADE. The 5 light set uses a 9 volt alkaline battery or your 6 cell car pack.
CAR RAM 66 RACER'S STOP LIGHT. Now R/C car racers have a small (1/2 x 1 inch) light (1 ounce) device featuring two, bright instrument bulbs with red lenses. Powered by the electric car battery pack, it will operate from 3 to 9 volts with either reversing or non reversing electronic speed controls.
CAR RAM 84 RECTANGULAR LIGHTS. This two light system provides headlights for R/C cars and trucks as well as shaped lighting for other model use. The 1/2 x 7/8" lenses are typical scale size and can be used on the "face" of a model. Each light has a 12" wire to the battery snap for a 9 volt Alkaline battery or the 6 cell car nicad battery can be used.
RAM 47 PROGRAMMABLE SEMAPHORE SIGNAL LAMP.
This device offers the ultimate scale effect for your ship model.
A Morse code message can be sent by controlling up to 32 flash impulses.
The interval between messages is also adjustable. Messages and intervals
can be simply changed. A 9 volt Alkaline battery is needed to power the
bright signal lamp.
PLASTIC MODEL LIGHTS
High brightness LEDs are used in the following systems. This eliminates any possible heat distortion of your plastic model. The 3 volt battery box (two AA cells) can often be mounted in a model or be made part of its display base or diorama. Smaller 3 volt batteries can be substituted. The use of new "white" LEDs provides accurate head lights etc. T1 LEDs are approximately 1/8" (3MM) diameter; T1-3/4 LEDs are approximately 3/16" diameter (5MM). Smaller "lights" can be simply replicated with our RAM 101 Light Pipe kit. All systems are completely assembled with 1 foot of high quality, flexible #30 wire to each LED.
LIGHTS FOR PLASTIC MODELS
Also See... ULTRA BRITES !
RAM 94 CAR HEAD LIGHTS & TAIL LIGHTS.
This set provides the basic night running lights for any car or truck. It includes 2, T1-3/4 white head lights, 2, T-1 red tail lights each with 1 foot of wire connected to a battery box.
RAM 95 4 FLASHING HAZARD LIGHTS. New
This set provides the amber flashing hazard light system standard on all vehicles. It includes 4, T1 LEDs each with 1 foot of wire connected to a flasher boards 5/16" x 5/8" x 7/8" and a battery box. controlled
RAM 96 8 CLEARANCE LIGHTS. New
This set provides 8 amber, non flashing lights typical of truck running boards, body outlines and trailers.
It includes 8, T1 LEDs each with 1 foot of wire connected to a battery box.
RAM 97 2 HEAD LIGHTS/LANDING LIGHTS, LARGE. New
This set provides the bright, white lights for either application.
It includes 2, T1 3/4 LEDs each with 1 foot of wire connected to a battery box.
RAM 98 2 HEAD LIGHTS/LANDING LIGHTS, SMALL. New
This set provides the bright, white lights for either application but for smaller scale use. It includes 2, T1 LEDs each with 1 foot of wire connected to a battery box.
RAM 99 NAVIGATION LIGHTS. New
This set provides the red, green and white lights necessary for any airplane or ship model. It includes 3, T1 LEDs each with 1 foot of wire connected to a battery box.
RAM 100 FLASHING NAVIGATION LIGHTS. New
This set provides the red, green and white flashing effect needed to make some models more realistic. It includes 3, T 1 LEDs each with 1 foot of wire connected to a 5/16" x 5/8" x 7/8" flashing board and a battery box.
RAM 101 LIGHT PIPE. New
This kit enables you to bring light to parts of your model where it is not practical or scale appropriate to mount LEDs. The kit includes 36 inches of fiber optic cable which provides a "light" .040 in diameter and simple shrink tubes for connecting the cable to the RAM LEDs. The cable can be cut to lengths appropriate for any model.
RAM 132 PARK FLYER LITES, This 6 gram, 3 lite system uses Ultra Brite LEDs with red green and clear lense caps for easy orientation and draws only 6 ma for a typical 10 minute flight from your 5 to 8 cell power battery. Simply tape the system to a park flyer up to 48" span and enjoy flying early or late when the wind conditions are most friendly. $24.95
RAM 133 MAX LITES, This system has two Ultra Brite white LED head lites with 2 red tail/stop lites controlled by a switch attached to the throttle servo and powered by a 6, 7 cell Nicd or a 9V alkaline (6 hours). Wire lengths and instructions offer installation on most popular Maxx gas and electric chassis. $29.95